Disposal of "misfired" rounds
 

Ok shot some 30-06 mil surplus. Primary hit-no boom. Now what? Any ideas on what to SAFELY do wiht the rounds???:confused:

Re: Disposal of "misfired" rounds
 

you can take a pair of pliers and pull the bullets.

Keep them pointed in a safe direction(both ends) and there shouldnt be much risk. Without a barrel to contain the pressure, if they go off they wont do much, but better safe than sorry. They might still be able to put out an eye.

Re: Disposal of "misfired" rounds
 

Thought that might be the answer. If the brass ain't too banged up, how do you get the primer out to reload the brass???:)

Re: Disposal of "misfired" rounds
 

Do you have a bullet puller of some sort?

If you reload, you can disassemble the cartridge and reuse the components.

If you don't reload, use a pair of pliers to pull the bullet out of the case; put the powder out in your yard--it's rich in nitrates and can make good fertiliser. :)

Re: Disposal of "misfired" rounds
 

Re: Disposal of "misfired" rounds
 

I didnt know if a kenetic puller would be as safe, is why I suggested the pliers. I havent used one though.

Re: Disposal of "misfired" rounds
 

Good thoughts-waste NOTHING. I swear this is the only thing that will allow a business to stay in business in the 21st century- NO outputs except saleable product and zero waste.

I would like to reload the milspec 30-06 stuff so the primer is a bit further out or at least flush. Most of the primers on the misfires were sunken so the firing pin did not ignite the powder.

Re: Disposal of "misfired" rounds
 

The kinetic pullers are plenty safe, and they're the only way to be able to reuse the bullet and brass. Pliers will cause damage.

Re: Disposal of "misfired" rounds
 

I will add it to my next midway bulk purchase!!:D

Re: Disposal of "misfired" rounds
 

ditch the pliers.. get a kinetic hammer and dismantle them. reload the brass with a good primer and reassemble the load and shoot it.

Re: Disposal of "misfired" rounds
 

The same way you always do, with the resizing die ? :confused:

Re: Disposal of "misfired" rounds
 

Oh I have everything for 7.62X39 except the press. I will need to get a set for 30-06. What is a good press that will accept ANY mfg dies? Or are the dies specific to the press??

Re: Disposal of "misfired" rounds
 

Ja but the primer did NOT fire:eek:

Re: Disposal of "misfired" rounds
 

You can deprime live primers. Take it slow. That has come up before. I think I remember 2 instances where they had them go off. Nothing major, if I remember correctly.

Re: Disposal of "misfired" rounds
 

I have deprimed live primers. As said, take it slow. Even if it goes off, it will probably try to blow it out of the primer pocket.

Two things to watch out for if you are using mil spec ammo.

1. Check down inside the case to see if there are two or one holes in the primer pocket. Some mil spec brass is "Berden primed" (two holes) which is a problem for depriming, and you need Berdden primers. http://www.youtube.com/watch?v=hth3Xwoqe9M shows a good summary.

2. Mil spec primer pockets are usually crimped. The crimp needs to be removed before you try to prime the brass. Midway has a number of tools that will remove the crimp. Or you can use a countersink on a drill...
http://www.thefirearmsforum.com/showthread.php?t=114039 has some good points.

You can use most dies in most presses; I think Dillon needs to use its own dies, but I may be wrong on that. There are plenty of Dillon users here. I have RCBS and I could use most makes of die on it.

Re: Disposal of "misfired" rounds
 

:mad:Very good info. Thanks. I am a little squirrely around live rounds. I had a 40mm Mk-19 round blow up in the feed tray (18 month old ammo with non-flush primers). The exploded casing sent pieces flying around the gun mount. I STILL like to find the QA inspector for that lot of ammo- I'd give a 40mm enema.:mad:

Re: Disposal of "misfired" rounds
 

Most all presses are threaded for 7/8X14 dies which is an industry standard now. The big presses (Le classic cast and RCBS Rockchucker) use bigger dies but come with a bushing for adapting to 7/8X14

Re: Disposal of "misfired" rounds
 

Just be carefull of some misfires as i have had a few that got real hot after i unloaded the gun. so i took the bullet first into the ground and pushed it in the ground and got away. just a few mins. latter that darn thing went off. So just a fare warning. I now take a bucket of water with me so if they do that i drop them in the water and its been a safer thing. I have had most of them be the old 303 brit ammo that have done this.

Re: Disposal of "misfired" rounds
 

Bad idea. By not seating the primer all the way (about .004 below flush) it leaves the firing pin to finish seating it creating a fail to fire. Just get yourself a press and dies and reuse the brass with quality components.

Re: Disposal of "misfired" rounds
 

Whatever you do just be careful. I always wondered what to do with them. I always thought about throwing misfired ammo out the window when going down the road. I dont want to have anything to do with ammo that I had in my weapon and the cartridge wouldnt go off.

Re: Disposal of "misfired" rounds
 

It's a PRIMER, not an ATOM BOMB.

It's got about the same potential as

a cap, from a cap gun. Relax.

Use gloves, and eye protection, if it'll make you feel better.

Re: Disposal of "misfired" rounds
 

You could get a collet bullet puller and do it that way as well that would be a little more safe than prying on it with pliers in your hand.

Re: Disposal of "misfired" rounds
 

just put your eyepro on and use the kinetic puller to retrieve the bullet and throw it in the decapper of choice and knock the primer out. If you're really worried about it going off, wear gloves and do it away from anything flammable; worst case it does go off, it ain't gonna hurt you. But I've never had one go off and I've banged on live ones (both hit and untouched) and nary a one has ever gone off. (watch, next one I do will explode on me... JINX!)

I would toss the powder, don't even try to guess what it is.

If the primer pocket is crimped, it will take some extra oomph to get the primer out but like said, just take it easy and tap it out.

Re: Disposal of "misfired" rounds
 

Thanks fellas. I used to throw my missfired or jammed 40mm over the side into the river. Can't do that now know better- I can not imagine how many Viet kid fishers have dredged ammo with a net that has gone off once they got it up and in the boat. JLA very good die data!!

Re: Disposal of "misfired" rounds
 

ditto what's been said.. except... on ammo that don't go off when i pull the trigger.. I leave the bbl pointed down range for a good minute.. then I setup to give it another hit on the firing pin only rarely have i had a real dud round i have once in a blue moon had a round that needed 2 strikes.

on the duds.. kinetic puller and reclaim what i can...