What does your reloading bench look like

Discussion in 'The Ammo & Reloading Forum' started by tEN wOLVES, Dec 26, 2008.

  1. gun-nut

    gun-nut Member

    Joined:
    Jan 15, 2011
    Messages:
    980
    Location:
    ohio
    Thanks Woolleyworm! It was some work but its nice to have room now. I just love looking at all these guys work benches. They look great for what kind of room that most people do have. Its neat to see how others utilize space.
  2. english jack

    english jack New Member

    Joined:
    Jan 6, 2012
    Messages:
    2
    Location:
    kent,uk
    thanks for the friendly welcome woolley,good to be here!
  3. ransom63

    ransom63 New Member

    Joined:
    Mar 31, 2011
    Messages:
    24
    I built mine from 2x4's, 5/8"oak plywood & deck anchors. The top is urethane coated, 22" wide, 8' from the long length & 6' from the short length. The whole thing is anchored to the wall & floor & can now be used as a tornado shelter! Lower shelves have become crammed with stuff, so the next project will be stacked shelves up against the walls. I only reload pistol calibers for now, so the one press is enough for me.

    Attached Files:

    Last edited: Jan 8, 2012
  4. JLA

    JLA Well-Known Member

    Joined:
    Feb 26, 2007
    Messages:
    18,271
    Location:
    Heart Of Texas
    Mine is currently a disaster area. I have been fairly busy with gun repairs these past few weeks. Need to clean up a bit I suppose.
  5. hillbillypaul

    hillbillypaul New Member

    Joined:
    Jan 3, 2010
    Messages:
    10
    Location:
    New York
    Mine is a mess, need to build some shelves. Doesn't look as bad as some. So benches are impressive. Gave me some ideas. 13 below zero this morning, i may have a project to do today. Thanks.. Paul
  6. woolleyworm

    woolleyworm Active Member

    Joined:
    Feb 23, 2009
    Messages:
    4,963
    Location:
    SW Fort Worth
    currently????????? :rolleyes::D:D:D


    -13* BBBBBRRRRRRRRR Had to put my jacket on just thinking about those kinda temps. I'd say it's a great day to do some work on the reloading bench; snap some before and after pics if ya don't mind.
  7. cpttango30

    cpttango30 Guest

    A few of mine.

    First bench. Built from a kit I found at Home Depot.
    [​IMG]

    First bench when I added my Dillon.
    [​IMG]

    The new bench. Went form a 2x4' to a 2x6'.
    [​IMG]

    Just finished it.
    [​IMG]

    5 minutes later. I swear that reloading benches have a super gravity well in the middle of them. As every time I build one It turns into a mess within 5 minutes.
    [​IMG]

    Finished bench with presses mounted. I am thinking of changing it up yet again.
    [​IMG]

    I have been beaning to change the pile of 2x6" the RCBS is mounted on to a Dillon Strong mount.

    [​IMG]

    Got tired of bending over to read the scale so I made a stand to hold it at eye level.
    [​IMG]

    [​IMG]

    [​IMG]
  8. cpttango30

    cpttango30 Guest

    Here is the reloading room I want.

    [​IMG]

    [​IMG]

    [​IMG]

    [​IMG]

    [​IMG]

    [​IMG]

    [​IMG]

    [​IMG]

    [​IMG]

    [​IMG]
  9. woolleyworm

    woolleyworm Active Member

    Joined:
    Feb 23, 2009
    Messages:
    4,963
    Location:
    SW Fort Worth
    Nice work Tango!
  10. oldgunfan

    oldgunfan Member

    Joined:
    Sep 12, 2006
    Messages:
    148
    Here is my messy corner of the basement

    Attached Files:

  11. UncleFudd

    UncleFudd Member

    Joined:
    Mar 23, 2008
    Messages:
    564
    Location:
    Phoenix, Az
    There are some beautiful, work areas here and I have gotten some ideas to improve upon what I have already. Thanks to all for sharing and to Ten Wolves for starting this thread.

    Mine is not as nice as Tango's dream room but it is my "Dawg House" and nice to be able to spend time in it during these snowy days.:D It is not my first loading room or bench, but I suspect at this time in life it is my last. So I am enjoying every minute I spend in it or with it to make it what I want, finally.

    Started as an apartment in our barn where we stayed for the first 12 years deciding to build a house. I was going to buy a 30' conex box to make my loading room when the wife suggested I use this room as we no longer use it since finishing the house. Bless her, she let me use the whole thing. I did have to store the cycle for safe keeping.;) and build the shelves for brass, powder and other components.

    Tool heads with dies, scales etc not up yet and still organizing will post when finished.
    I just finished the center bench and attached the loaders and loaded 150 rounds of 12 ga. New Years eve. Not even the tiniest vibration when pulling the handle.

    4, MEC, 9000 shot-shell loaders for 12, 20, 28 and 410 and the hulls all fit under the bench in tupper wear. A dillon 650 for all metalic loads for rifle and pistol and a Sinclare single for super accurate prairie dog loads. Lyman DPS111 for accurate powder measure and beam scale for checking any or all loads.
    RCBS kit for case trimming and primer pocket work.

    One other nice advantage is that my shooting benches are about 3o yards outside this room and I can shoot out to a mile or more against my own mountain, no neighbors to holler.:)


    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]

    UF
  12. woolleyworm

    woolleyworm Active Member

    Joined:
    Feb 23, 2009
    Messages:
    4,963
    Location:
    SW Fort Worth

    Holy Smokes, what are your business hours?? :D You're better stocked than my LGS !

    Nice room and even nicer wife for let'n ya use the whole thing!! Thats a sweet set-up.
  13. RustyFN

    RustyFN Member

    Joined:
    Oct 2, 2008
    Messages:
    622
    Location:
    West Virginia
    Very nice UncleFudd.
  14. hillbillypaul

    hillbillypaul New Member

    Joined:
    Jan 3, 2010
    Messages:
    10
    Location:
    New York
    Started to organize my bench last week dueb to morning temp of -13. Was inspired by this post and stole some ideas. Thanks. Due to work hrs cut to 30 hrs/week, funds to improve is $0.00. Original bench consisted of 1 solid core birch door blank cut to size. This week I scrounged some pieces of 1x8 shiplap pine and 1x8 novelty pine siding and added a shelf. Huge improvement. I have before and after pics. but can not get them posted. I have dial up internet and the 2 pics will not download completely. Only satellite high speed service is offered at near $100.00/ month. not happening. Will try again later.
  15. gun-nut

    gun-nut Member

    Joined:
    Jan 15, 2011
    Messages:
    980
    Location:
    ohio
    Send picks to someones email and i shure they will post them for ya. if not i will post them up for ya! I will send you a PM with my email.
Similar Threads
Forum Title Date
The Ammo & Reloading Forum Reloading/loading 22lrs-does anybody do it? Jan 30, 2009
The Ammo & Reloading Forum Does brand new .308 brass need to go through the re-sizing process Sep 22, 2014
The Ammo & Reloading Forum Does your SD ammo match your developed reload in recoil/accuracy? Jul 24, 2014
The Ammo & Reloading Forum RCBS Colored Boxes... What does it mean? May 23, 2014
The Ammo & Reloading Forum does this look familiar? Mar 1, 2014

Share This Page